Gluing vinyl flooring: which adhesive, which notched trowel?
If you want to lay glue-down vinyl, you need above all three things: a levelled, ready-to-cover subfloor, an adhesive for vinyl design coverings and the right tooth size on the trowel. For our vinyl glue-down planks, we recommend the wet-bed adhesive Bona D 750 according to the G² installation instructions, applied for example with the G² notched trowel no. 2. Vinyl glue-down planks are always bonded over the full surface.
In this guide we explain what a wet-bed adhesive is, how to check the subfloor, which tools you need and how installation works step by step. Whether glue-down or click vinyl suits your project better is covered in our comparison Glue-down or click vinyl? You can find the full range in the Vinyl design floors collection.
Quick decision guide
- Adhesive: Vinyl glue-down planks must be bonded over the full surface. We recommend the wet-bed adhesive Bona D 750. Always observe the adhesive data sheet.
- Notched trowel: The adhesive data sheet is decisive. The G² notched trowel no. 2 is intended for vinyl adhesives.
- Subfloor: Before gluing, the subfloor is always levelled with filler, in accordance with DIN 18365. Residual moisture must be measured before installation.
- Acclimatisation: Store the closed packs lying flat in the room for 48 hours at about 20 °C.
- Installation: According to the standards and regulations of DIN 18365. Apply adhesive, observe the flash-off time per the data sheet, lay the planks and rub or roll them down.
- Underfloor heating: Vinyl glue-down planks are approved for warm-water underfloor heating. The surface temperature must not exceed 29 °C.
Matching products at Gunreben
Vinyl wet-bed adhesive Bona D 750, 14 kg bucket: adhesive for vinyl and PVC design coverings, recommended by us for bonding the vinyl glue-down planks.
G² notched trowel for vinyl adhesive, tooth no. 2: the right tool for even application.
Traffic glue-down planks in country-plank format: 2.5 mm thick, for full-surface bonding, for example Ares or Athene.
Traffic glue-down planks in tile format: also for full-surface bonding, for example for bathroom, kitchen or hallway.
What is a wet-bed adhesive for vinyl flooring?
With a wet-bed adhesive, the adhesive is applied to the subfloor with the notched trowel and the covering is then laid into the still-wet adhesive bed. The subfloor absorbs part of the moisture. That is why this type of adhesive is intended for absorbent subfloors, i.e. a properly levelled screed.
According to the product description, the Bona D 750 is a one-component dispersion adhesive, fibre-reinforced and, according to the manufacturer's data sheet, solvent-free. It carries the EC1 mark and is intended for bonding vinyl and PVC design coverings in tile and plank format. It is supplied ready to use in a 14 kg bucket. Results depend on subfloor, room climate and workmanship, so the current adhesive data sheet from the manufacturer always applies.

The subfloor decides: how to check and prepare it
A thin glue-down covering shows every unevenness in the subfloor. Preparation is therefore the most important work step, even before the adhesive itself. Basic rule from our installation instructions: before gluing, the subfloor is always levelled with filler.
- Load-bearing capacity and cleanliness: The subfloor must be firm, load-bearing, clean and free of dust, grease, paint and adhesive residues. Loose areas and cracks are repaired.
- Levelling according to DIN 18365: The subfloor is levelled in accordance with DIN 18365. This also evens out unevenness that is still within the tolerances of DIN 18202. Let the filler dry according to the manufacturer's instructions.
- Measure residual moisture: The residual moisture of the subfloor must be measured before installation. The CM method is decisive (limits see table below). For heated screeds, the heating-up record also applies. If in doubt, have the measurement carried out by a specialist firm.
- Primer: Primers and bonding agents depend on the data sheet of the adhesive and the filler.
- Room climate: Only lay at the temperatures stated in the adhesive data sheet. The planks must be acclimatised beforehand (see next section).
| Screed | Max. residual moisture (CM) | With underfloor heating (CM) |
|---|---|---|
| Cement screed | 2.0 % | 1.8 % |
| Anhydrite screed | 0.5 % | 0.3 % |
Underfloor heating: Vinyl glue-down planks are approved for installation on warm-water underfloor heating. The surface temperature must not exceed 29 °C.
Tiles, old coverings and non-absorbent surfaces: The same applies here: filler is applied before gluing. Joints are levelled, and primer and filler must suit the old covering and the adhesive. Clarify the build-up beforehand using the data sheets. How this works in the bathroom is shown in our guide Vinyl flooring in the bathroom. If you have questions about your subfloor, we are happy to advise you, for example in the showroom in Hallstadt.
Before installation: acclimatise and check the goods
So that the planks adapt to the room climate, store the closed packs lying flat in the room for 48 hours at about 20 °C. Only open the packs during installation.
Check the planks for any transport and material damage in daylight before laying. Important: cut or installed goods are excluded from complaints. Differences in colour and structure are material-related and are not grounds for a complaint.
Which tooth size? The notched trowel for vinyl adhesive
The tooth size determines how much adhesive remains on the subfloor. Too little adhesive leads to poor bonding, too much can squeeze out at the joints when laying. Which tooth size belongs to the adhesive is stated in the manufacturer's data sheet. According to the product description, the G² notched trowel with tooth no. 2 has a spring-steel blade and is matched to vinyl adhesives.
| Tool / material | What for? | Note |
|---|---|---|
| Notched trowel no. 2 | Spread adhesive evenly on the subfloor | Intended for vinyl adhesives. Observe the adhesive data sheet. |
| Wet-bed adhesive Bona D 750 | Full-surface bonding of the vinyl glue-down planks | Recommended by us. Observe the adhesive data sheet. |
| Filler | Level the subfloor before every gluing | According to DIN 18365, must suit the subfloor and the adhesive |
| CM measuring device (or specialist firm) | Measure residual moisture of the screed | Mandatory before installation |
| Articulated roller or rubbing block | Press the covering into the adhesive bed | Work evenly and over the whole surface |
| Utility knife, straightedge, folding rule | Cutting the planks | Change the blade regularly |
You will find further accessories in the Vinyl accessories collection.
Laying glue-down vinyl: step by step
The existing standards and regulations in accordance with DIN 18365 apply to installation. The following steps give you an overview.
1. Laying plan and cutting
Plan the laying direction and row pattern before you apply adhesive. The last row at the wall should not become too narrow. Only open the packs now and mix planks from several packs so that the decor looks even.
2. Apply adhesive
Apply the adhesive in manageable areas that you can cover within the working time. Spread it evenly with the notched trowel. Take flash-off time and open time from the adhesive data sheet; they depend on room climate and subfloor.
3. Lay the planks
Start at a straight line and lay the planks butt to butt into the adhesive bed. Keep the joints tight, but without force. Adhesive that gets onto the surface is removed immediately according to the manufacturer's instructions.
4. Rub and roll down
Press the covering down firmly with a rubbing block or roller so that it has full-surface contact and no air pockets remain. Repeat this according to the adhesive manufacturer's instructions.
5. Edges and skirting
Finish the edge connections neatly and cover them with skirting that matches the floor. Which ones these are is shown in the guide Skirting boards for vinyl flooring. You will find matching profiles in the Vinyl skirting boards collection.
6. Walkability
When the floor may be walked on and loaded is stated in the adhesive data sheet.

Cleaning and care
Door mats and entrance zones protect the covering from dirt and abrasion from grit and sand. Felt glides should be used under furniture. Direct sunlight and intense artificial light can cause fading. High-heeled shoes and uncut animal claws can permanently damage the covering.
Loose dirt is simply swept or vacuumed. For routine cleaning we recommend the “Bona Cleaner”, a highly concentrated cleaning agent for daily cleaning. Diluted accordingly, it also removes heavy soiling. Further tips are in our guide Cleaning and caring for vinyl flooring.
Which glue-down plank suits your project?
Our Traffic glue-down planks are 2.5 mm thick and available in two formats: as country plank and in tile format. Details on wear layer, wear class and fire behaviour can be found in the product data of each product.
- Living room and bedroom: glue-down planks in country-plank format for a homely wood look, for example Luna or Hermes.
- Kitchen, hallway and office: country planks or tile format, depending on the desired look. For heavily used areas, pay attention to the wear class in the product data.
- Renovation with low build-up height: At only 2.5 mm thickness, glue-down planks add hardly any height, for example Thor. Here too, the subfloor is levelled beforehand.
- Bathroom: Glue-down vinyl is the usual choice, especially in tile format. Details on joints and edges in the guide Vinyl flooring in the bathroom.
You can see all decors in the Traffic glue-down plank 2.5 mm collection. If you prefer floating installation, you will find the click variant in the SPC vinyl collection.

Conclusion: good preparation, the right adhesive, the right tooth size
When gluing vinyl flooring, subfloor and workmanship decide the result. Level the subfloor according to DIN 18365, measure the residual moisture and acclimatise the planks for 48 hours. Then bond over the full surface with a wet-bed adhesive such as Bona D 750, applied with the matching notched trowel, and observe the information in the adhesive data sheet. Order adhesive and notched trowel together with your glue-down planks.
Would you like to see the decor in the room first? You can order samples via the “Request sample” tab on the individual products. The sample is free, you only pay the shipping costs.
Larger areas or projects? Floor layers, planners and businesses can send an enquiry via our business contact form or by e-mail to info@gunreben.de. Private customers can reach us via the contact page.
FAQ on gluing vinyl flooring
Answers to frequent questions on adhesive, notched trowel and installation.
There are special adhesives for vinyl and PVC design coverings. For our vinyl glue-down planks we recommend the wet-bed adhesive Bona D 750 for absorbent subfloors. The adhesive data sheet and the installation instructions of the covering are always decisive.
The tooth size depends on the adhesive. According to the product description, our G² notched trowel with tooth no. 2 is intended for vinyl adhesives. Check in the data sheet of your adhesive whether a different tooth size is required.
Click vinyl is intended for floating installation. Full-surface bonding only makes sense if the installation instructions of the respective product expressly provide for it. If you want to bond over the full surface, better choose a glue-down plank. Read more in the comparison Glue-down or click vinyl?
On tiles too, filler is applied before gluing. Joints are levelled, and primer and filler must suit the old covering and the adhesive. Which combination of build-up and adhesive fits is stated in the data sheets. Details can be found in the guide Vinyl flooring in the bathroom.
The time depends on the adhesive, the subfloor and the room climate. The information is in the adhesive manufacturer's data sheet. Observe it before walking on the floor or placing furniture.
